PuppyIP Resource Center
Network & Connection Troubleshooting 8 min read Published 2026-11-17

Xray relay cannot connect: separate the client entry, listener and NAT egress address

When an Xray relay cannot be reached, separate the local listener, the client-reachable entry and the outbound NAT address; they may be different values.

Xray relay NAT address listening port connection troubleshooting

Service eligibility and regional restrictions

PuppyIP serves only compliant overseas businesses and their authorized personnel. Proxy services are not available in mainland China. The service may only be used for lawful business activities outside mainland China. Use of this service within mainland China is prohibited.

Hosting a proxy IP or server overseas does not change these restrictions. The service must not be provided to end users in mainland China through relaying, forwarding, sharing or resale. Before use, read the Terms of Service.

Key Takeaways

  • An address observed for server egress is not necessarily able to receive new client connections.
  • Use ss and local interface data to check the bind, then inspect the source address selected by a route lookup.
  • With NAT, the public entry, port forward, security group and local listener must line up.
  • Correct the client entry only when evidence identifies it as wrong; a staged probe is not full Xray or UDP acceptance.

Separate the three address roles

An Xray relay can involve a local address where the service binds, an entry that clients dial and an outbound path the server uses to reach an upstream. Behind NAT or a cloud network, the source address seen externally may be translated by a gateway. That address may not forward back to this relay or expose the port clients need.

Do not copy a public egress address into a listener or client endpoint just because a service reports it. A listener must bind to an address configured on the host. A client entry must be reachable from the client's network and forwarded by the firewall, security group and port mapping to the intended listener.

Check the listener and local interfaces

Confirm the port used by the relay, then inspect its TCP listener and the host's local interface addresses. If ss shows no matching listener, the issue remains at the local service or configuration layer. A process bound to loopback is not directly reachable by an external client. Output may include public addresses or process details; inspect it only in an authorized environment and redact it before sharing.

Read the relay listener and local addresses

sh
PORT='REPLACE_WITH_CONFIGURED_LISTEN_PORT'
sudo ss -ltnp "sport = :$PORT"
ip -br address
Read-only check on Linux with iproute2. Replace the actual service port. This shows local interfaces and port ownership; it does not prove NAT or external reachability.

Keep egress source separate from the client endpoint

A route lookup shows the egress interface and source address selected when the server reaches an upstream IP. That source address describes traffic initiated by the server; it does not tell clients where to connect. Do not copy the reported src value into the relay's client address or listener setting.

Compare the relay entry in its management UI, the service's bind address, host routes, cloud security group and NAT forwarding rules. If the server uses dynamic egress or upstream NAT, confirm who manages the mapping and which local interface and port it forwards to before changing an endpoint.

Read the route selected for an upstream target

sh
PEER_IP='REPLACE_WITH_UPSTREAM_PEER_IP'
ip route get "$PEER_IP"
Linux route lookup; it does not modify the routing table. Replace the target with an authorized upstream IP. The reported src is selected for that outbound destination and is not automatically an inbound endpoint.

Probe the TCP entry from the client network

From an authorized client, check the relay entry's TCP handshake and compare its network, host, port and test time with the server listener. If the client cannot establish TCP while the local listener works, continue with public DNS, NAT forwarding, cloud security-group and host-firewall checks. Do not guess by cycling ports.

The entry should be a relay address or name reachable from that client network. If the configured field points to an outbound NAT address with no mapping back to the relay, change only the client-facing entry to a confirmed reachable address. Keep the port, transport, TLS/SNI and authentication identity unchanged so the result isolates one variable.

Probe the relay TCP port from an authorized client

sh
ENTRY_HOST='REPLACE_WITH_INBOUND_REACHABLE_RELAY_HOST'
ENTRY_PORT='REPLACE_WITH_CONFIRMED_LISTEN_PORT'
nc -vz -w 5 "$ENTRY_HOST" "$ENTRY_PORT"
Run on a client allowed to reach the relay using a netcat build that supports -w. Set the confirmed reachable entry and listener port. TCP success does not validate the Xray handshake.

Back up before changes and keep management access

Before editing the client profile or relay service, back up the exact configuration and record the original entry, listener port, service unit and management route. If the entry change requires a reload or restart, confirm that another authorized SSH session, cloud console or out-of-band route works, then use the management method supported by that release during a maintenance window.

Do not bind the service to a public NAT address that is not configured on the host, and do not open a broad range of management ports to the internet. If a control panel or generator owns the configuration, change it there so a later regeneration does not overwrite a manual edit.

Verify the required protocol end to end

After the TCP probe, complete an Xray protocol handshake, authentication and one authorized target request through the actual client profile. Confirm that the server selects the intended outbound path. A listener and TCP reachability cover only part of transport; they do not validate VLESS, TLS/SNI, user identity or routing rules.

If UDP is required, use a UDP-specific test supported by the Xray core, transport and client, and check the return traffic. One TCP or staged connection does not replace UDP, client, repeated-connection or long-duration checks. Record the network, protocol and config version; leave incomplete checks pending.

Sources

Frequently Asked Questions

Is the server's public egress IP always the address clients should use?

No. An outbound NAT source and a client-reachable entry serve different directions. Confirm inbound mapping, security groups and the local listener as well.

Why can clients fail when ss shows a listening port?

A local listener does not prove public reachability. Check its bind address, NAT forwarding, cloud security group, host firewall and the host and port used by the client.

Does a successful TCP probe prove Xray or UDP works?

No. It proves only that one TCP connection was established. Protocol handshake, authentication, routing and UDP need their own end-to-end checks.